Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
How do you actually feel in regards to Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult task. If the old bathtub is conveniently easily accessible, the task can relocate immediately; if you need to open a wall to remove the old tub and place the brand-new bath tub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will require an assistant to leave the old tub and also set in the new one. See to it you have certified on your own for the job and also fit attempting it. As opposed to working with a professional to take over a halfway-completed task, it is much better to consider utilizing one prior to you start. Chances are you might need a professional plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your bathroom if you have actually already bought a brand-new bathtub and do not require to alter the arrangement of your previous water pipelines.
Your tools and also product list ought to consist of the following:
Preparing for the Installment
Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, activate the taps to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be rather bothersome due to the limited gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the staying water that will originate from the pipes. When the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, place the bathtub in the needed setting. The wooden boards are handy in equally spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub until the spirit level reviews degree.
To mount taps, fit the bottom of the furthest flexible faucet port to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water supply and examine all joints as well as new pipework for leaks and also tighten them if essential. Fill up the tub and additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, take care of the bath paneling as described in the supplier's user's manual. Tiling and securing around the bath tub ought to wait until the bath tub has been used at the very least once as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in place between the tap and also the sink. Protect the faucet in position with the producer provided backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a stiff seal, creating the water to pass through the wall in between the bathroom and the tiling, causing complications with moisture and also feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill the tub with water prior to securing, to allow for the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our piece on Installing A Bathtub. Thanks for taking a few minutes to browse our short article. Loved our write up? Please share it. Help somebody else locate it. Thank you so much for taking the time to read it.
Book Service Now Report this page